Installation Guide - Tempo/Precedent
This video demonstrates how to install an IOTee TeeBox on a Club Car Tempo/Precedent with FLA or AGM Batteries
Drill
T15 & T30 drill bits
Pliers
Cleaning towel/Cloth
IOTee TeeBox & Fixings
Installation Time: 3 minutes per cart
For personal safety and to prevent damage to the TeeBox during installation, we recommend to put the cart in Tow before installation
Each TeeBox is sent pre-registered to the site and has the Site Name and Car Number printed on the top. We also supply corresponding QR code stickers with matching Car Number. It is critical that the correct sticker and device are placed on the same cart.
Locate the Run/Tow switch under the seat. Push this down into the Tow position
Remove the dash piece using the T15 & T30 drill bits
Use a cloth to clean the area behind the ignition barrel
Fix the velcro strips supplied in the box to the bottom and rear of the TeeBox
Position the TeeBox behind the dash, in the recessed area behind the ignition barrel. Use the velcro strips to secure into place and push the device firmly into position
Locate the Black/Red wires which supply the battery indicator. Using pliers, crimp the red/purple T-Tap connectors to each wire. The connectors will click when secured properly
Insert the Black & Red wires from the TeeBox into the corresponding T-Tap connectors. e.g. Red -> Red, Black -> Black
Bend the terminals on the ignition barrel 90 degrees. This helps make space for the TeeBox
Remove the Blue wire from the ignition barrel and connect it to the Blue wire from the TeeBox
Connect the other Blue wire from the TeeBox to the ignition barrel
Install the dash piece
Locate the Run/Tow switch under the seat. Put this up into the Run position
Remove the original sticker covering the steering wheel and clean and dirt or residue
Replace with the sticker supplied by IOTee. The Car Number will be printed on the sticker, make sure this matches the device number installed.
Use the camera on your phone to scan the QR code and open the link. If the device has not connected to 4G or WiFi, you will see an offline notification.
The device can take several minutes or longer in some cases to find a signal and connect. Leave the cart on, in Run, and contact IOTee if the device remains disconnected.
If you are installing multiple carts, instead of doing each cart one by one, it can be more efficient to remove all dashboards and install devices all at once.
Park carts in a line
Place a TeeBox on the seat of each cart
Remove all dashes and clean
Install all TeeBoxes
Install all dashes
Tools required:
Drill
T15 & T30 drill bits
Pliers
Cleaning towel/Cloth
IOTee TeeBox & Fixings
Installation Time: 3 minutes per cart
For personal safety and to prevent damage to the TeeBox during installation, we recommend to put the cart in Tow before installation
Each TeeBox is sent pre-registered to the site and has the Site Name and Car Number printed on the top. We also supply corresponding QR code stickers with matching Car Number. It is critical that the correct sticker and device are placed on the same cart.
Installation Instructions:
Locate the Run/Tow switch under the seat. Push this down into the Tow position
Remove the dash piece using the T15 & T30 drill bits
Use a cloth to clean the area behind the ignition barrel
Fix the velcro strips supplied in the box to the bottom and rear of the TeeBox
Position the TeeBox behind the dash, in the recessed area behind the ignition barrel. Use the velcro strips to secure into place and push the device firmly into position
Locate the Black/Red wires which supply the battery indicator. Using pliers, crimp the red/purple T-Tap connectors to each wire. The connectors will click when secured properly
Insert the Black & Red wires from the TeeBox into the corresponding T-Tap connectors. e.g. Red -> Red, Black -> Black
Bend the terminals on the ignition barrel 90 degrees. This helps make space for the TeeBox
Remove the Blue wire from the ignition barrel and connect it to the Blue wire from the TeeBox
Connect the other Blue wire from the TeeBox to the ignition barrel
Install the dash piece
Locate the Run/Tow switch under the seat. Put this up into the Run position
Remove the original sticker covering the steering wheel and clean and dirt or residue
Replace with the sticker supplied by IOTee. The Car Number will be printed on the sticker, make sure this matches the device number installed.
Verify Device Status:
Use the camera on your phone to scan the QR code and open the link. If the device has not connected to 4G or WiFi, you will see an offline notification.
The device can take several minutes or longer in some cases to find a signal and connect. Leave the cart on, in Run, and contact IOTee if the device remains disconnected.
Tips for Fleet Installs
If you are installing multiple carts, instead of doing each cart one by one, it can be more efficient to remove all dashboards and install devices all at once.
Here's how we do it:
Park carts in a line
Place a TeeBox on the seat of each cart
Remove all dashes and clean
Install all TeeBoxes
Install all dashes
Updated on: 17/03/2023
Thank you!